Output
Terminal output of remote execution
Action: servicePortsInfo at 1/11/2026, 11:20:01 AM
Huawei Integrated Access Software (MA5800).
Copyright(C) Huawei Technologies Co., Ltd. 2002-2017. All rights reserved.
-----------------------------------------------------------------------------
User last login information:
-----------------------------------------------------------------------------
Access Type : SSH
IP-Address : 10.228.153.11
Login Time : 11-01-2026 12:18:33+01:00
Logout Time : 11-01-2026 12:18:34+01:00
-----------------------------------------------------------------------------
OLTRibera_Ebre>scroll 512
OLTRibera_Ebre>enable
OLTRibera_Ebre#config
OLTRibera_Ebre(config)#display service-port port 0/6/10 ont 0
{ <cr>|e2e<K>|gemport<K>|sort-by<K>||<K> }:
Command:
display service-port port 0/6/10 ont 0
Switch-Oriented Flow List
-----------------------------------------------------------------------------
INDEX VLAN VLAN PORT F/ S/ P VPI VCI FLOW FLOW RX TX STATE
ID ATTR TYPE TYPE PARA
-----------------------------------------------------------------------------
210 103 common gpon 0/6 /10 0 1 vlan 103 10 10 down
211 139 QinQ gpon 0/6 /10 0 2 vlan other-all 11 11 down
212 139 QinQ gpon 0/6 /10 0 3 vlan other-all 1000 1000 down
-----------------------------------------------------------------------------
Total : 3 (Up/Down : 0/3)
Note : F--Frame, S--Slot, P--Port,
VPI indicates CM index for DOCSIS,
VPI indicates ONT ID for PON, VCI indicates GEM index for GPON,
v/e--vlan/encap, pritag--priority-tagged,
ppp--pppoe, ip--ipoe, ip4--ipv4oe, ip6--ipv6oe.
When FLOW TYPE is plist, the value of FLOW PARA is a byte in
hexadecimal format and indicates a priority list. Eight bits
of its binary value indicate priorities 0-7 from the least
significant bit to the most significant bit. Value 1 indicates
that the priority is used. For example, if FLOW PARA is 0x23 and
its binary format is 0010 0011, priorities 0, 1 and 5 are used
OLTRibera_Ebre(config)#
OLTRibera_Ebre(config)#quit
OLTRibera_Ebre#quit
Check whether system data has been changed. Please save data before logout.
Are you sure to log out? (y/n)[n]:y
Configuration console exit, please retry to log on
Action: servicePortsInfo at 1/11/2026, 11:20:01 AM
Huawei Integrated Access Software (MA5800).
Copyright(C) Huawei Technologies Co., Ltd. 2002-2017. All rights reserved.
-----------------------------------------------------------------------------
User last login information:
-----------------------------------------------------------------------------
Access Type : SSH
IP-Address : 10.228.153.11
Login Time : 11-01-2026 12:18:33+01:00
Logout Time : 11-01-2026 12:18:34+01:00
-----------------------------------------------------------------------------
OLTRibera_Ebre>scroll 512
OLTRibera_Ebre>enable
OLTRibera_Ebre#config
OLTRibera_Ebre(config)#display service-port port 0/6/10 ont 0
{ <cr>|e2e<K>|gemport<K>|sort-by<K>||<K> }:
Command:
display service-port port 0/6/10 ont 0
Switch-Oriented Flow List
-----------------------------------------------------------------------------
INDEX VLAN VLAN PORT F/ S/ P VPI VCI FLOW FLOW RX TX STATE
ID ATTR TYPE TYPE PARA
-----------------------------------------------------------------------------
210 103 common gpon 0/6 /10 0 1 vlan 103 10 10 down
211 139 QinQ gpon 0/6 /10 0 2 vlan other-all 11 11 down
212 139 QinQ gpon 0/6 /10 0 3 vlan other-all 1000 1000 down
-----------------------------------------------------------------------------
Total : 3 (Up/Down : 0/3)
Note : F--Frame, S--Slot, P--Port,
VPI indicates CM index for DOCSIS,
VPI indicates ONT ID for PON, VCI indicates GEM index for GPON,
v/e--vlan/encap, pritag--priority-tagged,
ppp--pppoe, ip--ipoe, ip4--ipv4oe, ip6--ipv6oe.
When FLOW TYPE is plist, the value of FLOW PARA is a byte in
hexadecimal format and indicates a priority list. Eight bits
of its binary value indicate priorities 0-7 from the least
significant bit to the most significant bit. Value 1 indicates
that the priority is used. For example, if FLOW PARA is 0x23 and
its binary format is 0010 0011, priorities 0, 1 and 5 are used
OLTRibera_Ebre(config)#
OLTRibera_Ebre(config)#quit
OLTRibera_Ebre#quit
Check whether system data has been changed. Please save data before logout.
Are you sure to log out? (y/n)[n]:y
Configuration console exit, please retry to log on
retCode
255